Gates and doors9 min read

Why the cheapest gate or door quote rarely costs the least, and how to compare manufacturers in the UAE

What a lower quote or a smaller shop usually leaves out, the questions to ask any gate or door maker, ours included, and how we answer them.

A cheaper gate or door quote is usually a quote for a different gate or door: thinner material, paint instead of a properly prepared powder coat, lighter hinges, a motor chosen on price, or installation and hardware left off the page. The difference rarely shows on handover day. It shows within a couple of UAE summers, as rust at the joints, a finish that chalks and lifts, a gate that sags onto its motor, or a door that swells. This guide is how to compare gate and door manufacturers fairly, what to ask any of them, ours included, and how we answer.

Black double gate with a gold disc and gazelle silhouettes
Ask about this one

Why does the cheapest gate quote rarely cost the least?

Because the money in a gate goes to four places, and a lower price has to come out of at least one of them.

  • The material: cast aluminium removes rust risk entirely; steel needs proper preparation to survive salt air, and lighter sections cost less but carry less.
  • Preparation and coating: salt air finds every weakness in a finish, from thin spots on edges to uncoated drill points. Wet paint chalks, fades and lifts at the edges within a couple of years, while a properly prepared and cured powder coat holds its colour far longer.
  • Hardware and automation: an underpowered motor on a heavy gate is the most common cause of early failure, and light hinges are where sagging starts.
  • Measuring and installation: a gate made to rough sizes and fitted by whoever is free that day jams, scrapes or strains its motor.

A lower quote that ends in repainting every couple of years, a new motor or a rehung gate is not a saving.

Bronze sliding gate with a diagonal pattern in front of a classical villa
Ask about this one

Is a smaller workshop or a cheaper option always worse?

No, and it would be unfair to say so. Plenty of small workshops weld honestly. The question is not the size of the shop but what the price includes and who controls each step: whether the gate is made and coated in one place, or passed between a fabricator, an outside coater and a separate fitter, each on their own schedule. When something goes wrong between them, accountability tends to disappear in the gaps.

What should you compare between gate and door manufacturers?

What to compareWhat a lower quote often leaves outHow we do it
Where it is madeBought in, or made in one shop and finished in anotherCut, welded, finished and installed by us, from our own Fujairah workshop, with no subcontracted steps
Preparation and coatingSpray paint, or powder coat at an outside coater, on its schedule and in a shared batchSandblasted, zinc phosphate primer, then powder coated on our own line and cured at 200°C, with film thickness checked at edges and drill points
Material for the coastPlain steel under a coat of paintCast aluminium where rust is the risk; steel where span and security lead, prepared for salt air
Hardware and motorLight hinges, and a motor chosen on priceHinges and handles included in the gate price; the motor sized to the weight of the gate and fitted with it
MeasuringSizes taken from photos or a drawingA free site visit within 48 hours to measure the opening as built
The quotationOne lump sumItemised: material, finish, hardware and installation line by line, with the material and finish written down
InstallationWhoever is free, or a subcontracted fitterOur own team, with committed dates written into the quotation
MatchingGate, railings and doors from different suppliers, in different colour batchesGate, fencing and side door coated in one batch, so the colours match
After handoverUnclear who to callWarranty on workmanship and powder coated finishes, from a workshop that has been in Fujairah since 1984
Modern villa with a black sliding gate and side door
Ask about this one

What about doors?

The same logic applies, and a door quote is even easier to misread. A price for a door leaf alone is not comparable with a price for a door that comes with its frame, architraves, handle, lock and hinges, so we quote the complete set, each item on its own line, plus installation. Material matters as much as on a gate: a hollow core or MDF door in a bathroom swells, and WPC does not. Main doors we make in cast aluminium or steel, powder coated on our own line; solid wood doors come from our own carpentry workshop; WPC doors are supplied to the sizes we measure, and WPC room doors start from AED 1,000 for the standard specification. Comparing steel or metal door manufacturers in the UAE comes down to the same questions as gates, listed below.

Carved dark brown double door with gold detailing in an arched entrance
Ask about this one
Bronze and gold powder coated door with a diamond pattern
Ask about this one

Which questions should you ask any gate or door maker?

  1. Is it made in your own workshop, or bought in?
  2. Who coats it, how is the steel prepared, and is it powder coat or paint?
  3. Which material do you suggest for my location, and why?
  4. Are the hinges, handles and locks in the price? Is the motor sized to the weight of the gate?
  5. Will you measure on site, and who installs?
  6. Is the quotation itemised, with the material and finish written down?
  7. What does the warranty cover, and who comes back if something needs adjusting?

Ask them of us too. Our answers are in the table above, and they are written into every quotation.

"A gate is bought once and looked at every day. A cheaper quote is only cheaper if it is for the same gate."

Why does a Fujairah workshop matter on the east coast?

Because measuring, installing and adjusting are site work, and distance decides how quickly they happen. Our workshop is in the Al Hail Industrial Area, Fujairah, so for homes in Fujairah City, Dibba Al Fujairah, Masafi and Mirbah, in the east coast towns of Kalba and Khorfakkan, and in Hatta, the measuring visit and any later adjustment are a short drive rather than a trip across the mountains. We also make and fit gates and doors across the rest of the UAE: in Dubai, Abu Dhabi, Sharjah, Ajman, Ras Al Khaimah, Umm Al Quwain and Fujairah.

Villa with black and gold ornamental gates
Ask about this one

What does a gate cost with us, and how long does it take?

Our gates start from AED 800 per square metre, with hinges and handles included; motors for automatic gates are quoted as their own line. The final figure follows the design, the material and the size, and the itemised quotation arrives within 24 hours of the free site visit. A custom gate typically takes 2 to 3 weeks from design approval to installation, depending on size, pattern and finish.

Who makes our gates and doors?

We do, in Fujairah, as we have since 1984. Al Taher began as a small carpentry workshop in the Al Hail Industrial Area and is still family run, now with two workshops: carpentry and aluminium, and DAT Metal Fabrication with its own powder coating line. Cutting runs on our own CNC machine, CAD drawings are produced in house when a design needs them, and you get WhatsApp updates and photos while your gate or door is being made.

Comparing quotes?

Send us the other quotation and photos of your entrance on WhatsApp, and we will show you, line by line, what ours includes. The site visit is free and takes place within 48 hours.

Book a free site visit

Read powder coating vs painting for metal gates, see metal gate designs and door design ideas, or browse our custom metal gates service.

Frequently asked questions

Why are some gate quotes so much cheaper?

Usually because the gate is not the same: lighter sections, paint instead of a prepared powder coat, light hinges, a motor chosen on price, or installation and hardware left out. Compare itemised quotations line by line before comparing totals.

Is a small workshop a bad choice for a gate?

Not necessarily. What matters is who controls each step: whether the gate is made, coated and installed by one company, or passed between a fabricator, an outside coater and a separate fitter. Ask any maker the same questions about material, coating, hardware, measuring and warranty.

Is powder coating worth it over paint for a gate?

In UAE sun and coastal air, yes. Wet paint tends to chalk, fade and lift at the edges within a couple of years, while a properly prepared and cured powder coat holds its colour and adhesion far longer.

What should a gate quotation include?

The material, the finish, the hardware and the installation, each on its own line, with the material and finish written down. Our gate prices include hinges and handles; motors for automatic gates are quoted as their own line.

Do you make gates and doors in your own workshop?

Yes. Gates and metal doors are cut, welded, finished and powder coated in our own Fujairah workshops, and solid wood doors come from our carpentry workshop; WPC doors are supplied to the sizes we measure. Our own team installs everything.

How much does a custom gate cost?

Our gates start from AED 800 per square metre, with hinges and handles included. The final figure follows the design, material and size, and the itemised quotation arrives within 24 hours of the free site visit.

Do you make gates and doors for homes in Kalba, Khorfakkan, Dibba and Dubai?

Yes. Our workshop is in Fujairah, close to Dibba, Masafi and the east coast towns of Kalba and Khorfakkan, and we make and fit gates and doors across all seven emirates, including Dubai and Abu Dhabi.